Hydrocultuur tool
RO & Kraanwater Mengcalculator
Meng omgekeerd osmosewater en kraanwater om de juiste start-EC voor hydrocultuur, binnenkweek en voedingsbereiding te schatten.
Final amount of mixed water you want to prepare.
Choose liters or US gallons.
Electrical conductivity of your source tap water.
Electrical conductivity of your reverse osmosis water.
Desired EC before adding nutrients.
Recommended products for water preparation
Waterbereidingsproduct
Een nuttig product voor het mengen van water, het controleren van EC of het stabiliseren van uw startoplossing.
Waterbereidingsproduct
Een nuttig product voor het mengen van water, het controleren van EC of het stabiliseren van uw startoplossing.
Waterbereidingsproduct
Een nuttig product voor het mengen van water, het controleren van EC of het stabiliseren van uw startoplossing.
Final amount of water you want after mixing.
Choose liters or US gallons.
Base EC of your tap water.
Base EC of your RO water.
Desired starting EC before nutrients.
Approximate pH of your tap water.
Approximate pH of your RO water.
Tap water usually influences final pH more strongly than RO. Increase this if your tap water is highly buffered.
The pH result is an estimate only. Real mixed pH depends strongly on alkalinity, bicarbonates, dissolved minerals, and how stable your source water is. Always verify pH with a calibrated meter after mixing.
Recommended products for RO and tap water blending
Waterbereidingsproduct
Een nuttig product voor het mengen van water, het controleren van EC of het stabiliseren van uw startoplossing.
Waterbereidingsproduct
Een nuttig product voor het mengen van water, het controleren van EC of het stabiliseren van uw startoplossing.
Waterbereidingsproduct
Een nuttig product voor het mengen van water, het controleren van EC of het stabiliseren van uw startoplossing.
Final amount of mixed water you want to make.
Choose liters or US gallons.
Enter the tap water share of your final blend.
EC of your tap water.
EC of your RO water.
Recommended products for mixed source water
Waterbereidingsproduct
Een nuttig product voor het mengen van water, het controleren van EC of het stabiliseren van uw startoplossing.
Waterbereidingsproduct
Een nuttig product voor het mengen van water, het controleren van EC of het stabiliseren van uw startoplossing.
Waterbereidingsproduct
Een nuttig product voor het mengen van water, het controleren van EC of het stabiliseren van uw startoplossing.
RO and tap water mixing calculator for hydroponics and indoor growing
This RO and tap water mixing calculator helps growers blend reverse osmosis water and tap water to reach a target starting EC before adding nutrients. It is useful for hydroponics, coco, DWC, recirculating systems, drip irrigation, and indoor growing where source water quality affects nutrient stability and plant performance.
Use it to estimate the right blend ratio, prepare reservoir water more consistently, and reduce the guesswork when you want softer starting water than straight tap water but more mineral content than pure RO.
How this water mixing calculator works
The calculator uses weighted blending based on source water EC values. Because EC behaves approximately linearly when two water sources are mixed, the tool can estimate the tap-water fraction needed to reach a selected target EC.
What each parameter means
- Tap water EC: electrical conductivity of your tap water before nutrients.
- RO water EC: electrical conductivity of your reverse osmosis water.
- Target mixed EC: the EC you want to start with before adding feed.
- Target water volume: final total amount of mixed water.
- Tap water percentage: chosen ratio of tap water in the blend.
- Alkalinity weight: rough weighting factor showing how strongly tap water may dominate final pH.
Why growers mix RO and tap water
Pure RO water is very clean but may start too soft for some feeding strategies, while tap water may contain too much mineral content, sodium, or bicarbonate. Mixing the two gives growers more control over starting EC and often creates a more manageable base for nutrients, CalMag, and pH adjustment.
This is especially helpful when tap water is too hard for direct use but fully pure RO is not the desired starting point.
About the pH estimate
Unlike EC, pH does not mix in a simple straight-line way because alkalinity and buffering capacity matter a lot. This tool provides only a practical weighted estimate in advanced mode. Real mixed pH can differ depending on bicarbonates, dissolved minerals, and source-water chemistry.
Always measure actual pH after blending and again after adding nutrients.
Best practice for growers
- Measure both tap and RO water with a calibrated EC meter.
- Blend water first, then add nutrients.
- Check EC again after mixing to confirm the estimate.
- Adjust pH only after the final nutrient solution is complete.
- Keep notes on the blend ratios that work best for your system and source water.
Verzending. 3 dagen EU-levering
7 tot 15 EUR onder 30kg. Zie meer op de Verzendingsdetails pagina.
60 dagen retourneren
U kunt een terugbetaling of vervanging krijgen tot 30 dagen na aankoop.
Maar we staan meestal aan de kant van de klant, dus we kunnen een tijdlijn van 60 dagen geven!
2 maanden deskundige ondersteuning na verkoop
Het is gratis.
Wij zijn een team van 10 met een decennium aan waardevolle ervaring in het kweken en tuinieren, dus als u hulp nodig heeft, begeleiden we u binnen 2 maanden na aankoop naar uw doel.
Over ons. Onze 9-jarige geschiedenis
GoToGarden begon in 2017 uit persoonlijke frustratie. Onze oprichter was een hobbykweker die uren doorbracht met het navigeren op online winkels die aanvoelden alsof ze waren gemaakt door mensen die nog nooit een plant hadden aangeraakt - rommelige lay-outs, vage productbeschrijvingen, geen echte begeleiding bij wat je daadwerkelijk moest kopen of waarom. Hij wist dat er een betere manier moest zijn.
Zie meer op de Over ons pagina
Bekijk andere calculators!
Schat voedingsstoffen, verlichting, VPD, irrigatie, plantafstand, kweekplanning, etc.