Hydroponikverktyg
Kalkylator för blandning av RO- och kranvatten
Blanda omvänd osmosvatten och kranvatten för att uppskatta rätt start-EC för hydroponik, inomhusodling och näringstillredning.
Final amount of mixed water you want to prepare.
Choose liters or US gallons.
Electrical conductivity of your source tap water.
Electrical conductivity of your reverse osmosis water.
Desired EC before adding nutrients.
Recommended products for water preparation
Produkt för vattenberedning
En användbar produkt för att blanda vatten, kontrollera EC eller stabilisera din startlösning.
Produkt för vattenberedning
En användbar produkt för att blanda vatten, kontrollera EC eller stabilisera din startlösning.
Produkt för vattenberedning
En användbar produkt för att blanda vatten, kontrollera EC eller stabilisera din startlösning.
Final amount of water you want after mixing.
Choose liters or US gallons.
Base EC of your tap water.
Base EC of your RO water.
Desired starting EC before nutrients.
Approximate pH of your tap water.
Approximate pH of your RO water.
Tap water usually influences final pH more strongly than RO. Increase this if your tap water is highly buffered.
The pH result is an estimate only. Real mixed pH depends strongly on alkalinity, bicarbonates, dissolved minerals, and how stable your source water is. Always verify pH with a calibrated meter after mixing.
Recommended products for RO and tap water blending
Produkt för vattenberedning
En användbar produkt för att blanda vatten, kontrollera EC eller stabilisera din startlösning.
Produkt för vattenberedning
En användbar produkt för att blanda vatten, kontrollera EC eller stabilisera din startlösning.
Produkt för vattenberedning
En användbar produkt för att blanda vatten, kontrollera EC eller stabilisera din startlösning.
Final amount of mixed water you want to make.
Choose liters or US gallons.
Enter the tap water share of your final blend.
EC of your tap water.
EC of your RO water.
Recommended products for mixed source water
Produkt för vattenberedning
En användbar produkt för att blanda vatten, kontrollera EC eller stabilisera din startlösning.
Produkt för vattenberedning
En användbar produkt för att blanda vatten, kontrollera EC eller stabilisera din startlösning.
Produkt för vattenberedning
En användbar produkt för att blanda vatten, kontrollera EC eller stabilisera din startlösning.
RO and tap water mixing calculator for hydroponics and indoor growing
This RO and tap water mixing calculator helps growers blend reverse osmosis water and tap water to reach a target starting EC before adding nutrients. It is useful for hydroponics, coco, DWC, recirculating systems, drip irrigation, and indoor growing where source water quality affects nutrient stability and plant performance.
Use it to estimate the right blend ratio, prepare reservoir water more consistently, and reduce the guesswork when you want softer starting water than straight tap water but more mineral content than pure RO.
How this water mixing calculator works
The calculator uses weighted blending based on source water EC values. Because EC behaves approximately linearly when two water sources are mixed, the tool can estimate the tap-water fraction needed to reach a selected target EC.
What each parameter means
- Tap water EC: electrical conductivity of your tap water before nutrients.
- RO water EC: electrical conductivity of your reverse osmosis water.
- Target mixed EC: the EC you want to start with before adding feed.
- Target water volume: final total amount of mixed water.
- Tap water percentage: chosen ratio of tap water in the blend.
- Alkalinity weight: rough weighting factor showing how strongly tap water may dominate final pH.
Why growers mix RO and tap water
Pure RO water is very clean but may start too soft for some feeding strategies, while tap water may contain too much mineral content, sodium, or bicarbonate. Mixing the two gives growers more control over starting EC and often creates a more manageable base for nutrients, CalMag, and pH adjustment.
This is especially helpful when tap water is too hard for direct use but fully pure RO is not the desired starting point.
About the pH estimate
Unlike EC, pH does not mix in a simple straight-line way because alkalinity and buffering capacity matter a lot. This tool provides only a practical weighted estimate in advanced mode. Real mixed pH can differ depending on bicarbonates, dissolved minerals, and source-water chemistry.
Always measure actual pH after blending and again after adding nutrients.
Best practice for growers
- Measure both tap and RO water with a calibrated EC meter.
- Blend water first, then add nutrients.
- Check EC again after mixing to confirm the estimate.
- Adjust pH only after the final nutrient solution is complete.
- Keep notes on the blend ratios that work best for your system and source water.
Frakt. 3 dagars EU-leverans
7 till 15 EUR under 30 kg. Se mer på sidan Leveransinformation.
60 dagars retur
Du kan få återbetalning eller ersättning upp till 30 dagar efter köpet.
Men vi står oftast på kundens sida, så vi kan ge en tidsram på 60 dagar!
2 månaders experthjälp efter köp
Det är gratis.
Vi är ett team på 10 personer med tio års gedigen erfarenhet av odling och trädgårdsarbete, så om du behöver hjälp guidar vi dig till ditt mål inom 2 månader från köpet.
Om oss. Vår 9-åriga historia
GoToGarden startades 2017 på grund av personlig frustration. Vår grundare var en hobbyodlare som spenderade timmar med att navigera onlinebutiker som kändes byggda av personer som aldrig hade rört en växt — röriga layouter, vaga produktbeskrivningar, ingen riktig vägledning om vad man faktiskt skulle köpa eller varför. Han visste att det måste finnas ett bättre sätt.
Se mer på sidan Om oss
Kolla in andra kalkylatorer!
Uppskatta näringsämnen, belysning, VPD, bevattning, växtavstånd, odlingsplanering, etc.